Torque Arm Slider Installation

Kyle Roehner	Accord Speedway Sportsman Crate 602
Steve Bernier	Autodrome Drummond Quebec Sportsman
David Hebert	Autodrome Drummond Quebec 358
Steve Bernier	Autodrome Granby Quebec Sportsman
Francois Bernier	Autodrome Granby Quebec 358
Adam Pierson	Bear Ridge Speedway
Tim Sears	Brewerton Speedway
Matt Sheppard	Brewerton Speedway
Jordon Watson	Bridgeport Speedway Crate
Dan Cogdill Jr.	Bridgeport Speedway Rookie Modifieds
Chris Herbison	Brockville Speedway Sportsman
Danny O Brien	Brockville Speedway 358
Josh Van Brocklin	Can Am Speedway Sportsman
Billy Dunn	Can Am Speedway 358
Dan Wiesner	Canandaigua Speedway Sportsman
Matt Sheppard	Canandaigua Speedway Big Block
Randy Howe	Cannan New Hampshire
Timmy Sears Jr.	Cayuga County Speedway Sportsman
Mike Mahaney	Cayuga County Speedway 358
Chris Herbison	Cornwall Speedway / Sportsman
Jordon Watson	Delmar Delaware AC DELCO Sportsman
Matt Jester	Delmar Delaware Big Block
Nick Petrilak	Five Mile Point Speedway Sportsman
Ron Davis III	Fulton Speedway Novice 525 GM Crate division
Billy Decker	Fulton Speedway Big Block
Bodie Bellinger	Glen Ridge Speedway Sportsman
Kenny Tremont Jr.	Glen Ridge Speedway Big Block / 358
Brad Rouse	Humberstone Speedway Sportsman
Chad Brachmann	Humberstone Speedway 358
Jim Gabriel Jr.	I88 Speedway / Afton N.Y.
Kenny Tremont Jr.	Lebanon Valley Speedway Big Block
Jeremiah Shingledecker	Lernerville Speedway
Jimmy Holden	Mercer Raceway Park
Brad Rouse	Merrittville Speedway Sportsman
Pete Bicknell	Merrittville Speedway 358
Dylon Evoy	Mohawk Speedway Sportsman
Rocco Infante	New Egypt Speedway Sportsman
Billy Pauch	New Egypt Speedway Big Block
Gary Edwards Jr.	Orange County Fairgrounds Sportsman
Tommy Meier	Orange County Fairgrounds Big Block
Mike Nagel Jr.	Penn Can Speedway Sportsman
Steve Bernier	RPM Speedway St Marcel Quebec / Sportsman
David Hebert	RPM Speedway St Marcel Quebec / 358
Don Spatarico	Ransomville Speedway Sportsman
Chad Brachmann	Ransomville Speedway 358
Rex King	Sharon Speedway
Chris Stull	Skyline Speedway
Randy Brown	Sportsman Speedway / Knox P.A.
Eddie White	Thunder Mountain Speedway
Matt Janczuk	Utica Rome Speedway Sportsman
Roger Williams	Woodhull Speedway Sportsman
Billy Van Pelt	Woodhull Speedway 358
Francois Bernier	Quebec SUPER SERIES CHAMPION
Thomas Burge	Louisianna State Champion
Bodie Bellinger	DIRTCar Sportsman Mr. DIRT Point Champion
David Hebert	DIRTCar 358 Mr DIRT Car Point Champion
Matt Sheppard	DIRTCar Big Block MR DIRT Point Champion
Rex King Sr.	BRP MODIFIED Tour Champion
Billy Pauch	AMERICAN RACER CUP CHAMPION

Tim Sears	Mr.DIRTCar Sportsman Series Champion
Danny Johnson	Mr.DIRTCar 358 Series Champion
Matt Sheppard	Mr.DIRTCar Big Block Series Champion
Jeff Crambo	ROC Champion Sportsman
Billy Decker	ROC Champion Big Block
Matt Sheppard	DIRTCar Big Block MR DIRT Point Champion

Twitter Update

Search

1.	First, ensure that the slider heim (BRP 424) is the proper length. It should be 2 1/4" from the center of the heim to the end of the threads. This is very important as it sets the pinion angle. If the heim came as part of a kit purchased from Bicknell Racing Products, it will be cut to the proper length. If it was not purchased from Bicknell Racing Products, we cannot be responsible for an improper length heim.
2.	Next, be sure the torque arm rubbers are the correct length. For a dry slick track, the torque arm rubbers can be cut down to as much as 1 1/8". For a heavy track, you may be better to leave the rubbers to their shipped length. Be sure to make the rubbers no less than 1 1/8" as the rubbers will not have any compression if they are too short.
3.	Prior to installation, ensure the slider rods (BRP 421) will slide with ease into the chassis. If they don't, clean the slugs out with a drill or a die grinder. If the slugs are a little snug it is okay, it just be harder to take them out if you ever have to.
4.	Install the rods, safety locks, and the aluminum slider plate. Be sure slider plate (BRP 418) slides through entire length of slider. Make sure the grease fittings face the bottom of the chassis.
5.	Next, Install the heim. Be sure the steel sleeve goes between the 2 washers. Also be sure the bolt tightens all the way up.

Back to the top

Name:
Email:
How many eyes has a typical person? (ex: 1)